IMPORTANT FOR LASER PRODUCTS
CAUTION:
Precautions
1. CLASS 1 LASER PRODUCT
•
Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
Basic and Common Operations
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
Notes on the power cord
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always
pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or
moving the System.
Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
Press
System Remote
To
Indication/Result
STANDBY lamp
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
MICRO COMPONENT SYSTEM
Point at the remote sensor on the front panel.
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
UX-G355
•
Select a source
See “Playing Back a Disc/USB Mass Storage Class Device” on page 4.
CD
CD
—Consists of CA-UXG355 and SP-UXG355
USB
MEMORY
USB
Avoid moisture, water, dust, and high temperatures
For turning off the demonstration display, see “Display
Demonstration” on page 3.
CAUTION:
• Do not place the System in moist or dusty places.
When using the remote
control
Press repeatedly to select “TUNER FM” or
“TUNER AM.”
• See “Listening to FM and AM Broadcasts” on
page 5.
Excessive sound pressure from earphones or headphones
can cause hearing loss.
•
If water gets inside the System, turn off the power and remove
the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
TUNER
TUNER FM TUNER AM
AUDIO IN
CAUTION: Proper Ventilation
• Do not expose the System to direct sunlight or place it near
a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too
cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
AUDIO IN
AUDIO
See “Listening to Other Equipment” on page 5.
CAUTION
IN
TUNER
Battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in
the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
Thank you for purchasing a JVC product.
VOLUME
Adjust the volume
Adjustable range: Level 0 (“VOL MIN”) to level 40 (“VOL MAX”).
INSTRUCTIONS
VOLUME
LVT1981-015A[US,A,UB,UW]
0209YAMMDWCDT
FADE
Drop the volume in
a moment
To restore the volume, press again, or adjust the volume level.
MUTING
Front view
—
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes
wrong, unplug the power cord and consult your dealer.
[European Union only]
©2009 Victor Company of Japan, Limited
Emphasize the
sound (Sound
Turbo)
The S.TURBO indicator lights up.
To cancel this function, press again.
SOUND TURBO
SOUND
TURBO
Warnings, Cautions and Others
CAUTION
Reinforce the bass
sound (Hyper Bass
Sound)
The BASS indicator lights up.
• When Sound Turbo function is activated (see above), the BASS indicator
goes off and HBS button does not work.
HBS
—
—
The
button in any position does not disconnect the
To cancel this function, press again.
mains line.
Side view
BASS/TREBLE
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain
readily operable.
• When the system is on standby, the STANDBY lamp lights
red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
Mains (AC) Line Instruction (not applicable for Australia and Hong Kong)
PHONES jack
Adjust the tone
(Bass/Treble)
Press once for adjusting the bass level; twice for treble level, then, press
VOLUME +/–.
Adjustable range: –3 to +3.
Headphones
(not supplied)
Stereo mini plug cord
Main unit (rear view)
Display Demonstration
VOLUME
DIMMER
When you plug in the System, the display demonstration automatically starts.
To cancel the display demonstration, press and hold DEMO until “DEMO CLR” is
displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does not work (and
you cannot deactivate it).
Dim the display
You can dim the display window and illumination lamp.
While the System is turned on...
ECO /
DIMMER
• When the display demonstration is activated, it also starts if no operation is done
for about 2 minutes while the System is turned on.
DEMO
CAUTION:
CLOCK/
TIMER
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Set the clock and
timer
For setting the clock, see “Setting the Clock and Using Timers” on page 6.
—
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Change the display
information
The display information changes as follows:
FM/AM: Clock = Frequency
DISPLAY
—
CD: Current track elapsed time = Clock
MP3/WMA: Current track elapsed time = ID3 tag = Current group/track
= Clock
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and headphones
when you turn on the System or start playback.
CAUTION for mains (AC) line
Set the ECO
(Ecology) Mode
Press when the System is on standby.
Setting the ECO (Ecology) Mode allows you to reduce power consumption
by turning the display off while on standby.
BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector
switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a
damage or risk of fire/electric shock.
ECO /
DIMMER
—
DEMO
The operations on pages 4 to 6 are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button names,
they can also be used for the operations.
To cancel this function, press again when the System is on standby.
1
3
Getting Started
Playing Back a Disc/USB Mass Storage Class Device
This System can play back...
Do not connect the AC power cord until all other connections have been made.
Supplied Accessories
Connections
Basic Disc/USB Mass Storage Class Device Operations
Playing Repeatedly—Repeat Play
– Audio CD.
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXG355U (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed in the remote control
when shipped from the factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
• AC plug adapter (× 1) (not supplied for Australia and Hong
Kong)
If anything is missing, consult your dealer immediately.
Press repeatedly to specify the repeat mode as follows:
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
REPEAT
To
Press
Indication/Result
1
2
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
To assemble the AM loop antenna
To connect the AM loop antenna (supplied)
1:
Repeats the current (or specified) track.
Repeats all tracks in the current group
(MP3/WMA only).
Play back the disc
• Current track number and elapsed playing
time appear.
• During playback, press again to pause.
:
CD
AM loop antenna (supplied)
Turn it until the best reception is obtained.
Play back the USB
mass storage class
device
ALL:
Repeats all tracks.
FM antenna (supplied)
USB
No indicator (Off): Normal playback
Loading a Disc (on the System only)
NOTE: Keep the AM loop antenna cable
wrapped around the AM loop antenna frame,
otherwise the effectiveness and sensitivity of
the AM loop antenna may be reduced.
or
CD
USB
Press to open the disc tray.
Stop playback
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
1
2
For better FM reception
Outdoor FM antenna
(not supplied)
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Programming the Playing Order—Program Play
Select a track
Select the next tracks.
Black
During stops, press so that the PRGM (program) indicator
lights up.
Disconnect the supplied FM antenna, and connect to
an outdoor FM antenna using a 75 Ω wire with coaxial
type connector.
Prepare the Remote Control
PROGRAM
1
2
When you use the remote control for the first time, pull out
the insulation sheet.
To go back to the beginning of the current or
previous tracks.
Select a track number.
White
Insulation sheet
or
Select a group
(MP3/WMA only)
Select the next groups.
UP
Press to close the disc tray.
3
Select the previous groups.
DOWN
Rear view
Press to program the selected track.
SET
3
4
5
Forward search/
Reverse search
Press and hold to fast-forward the track during
playback.
To stop searching, release the button.
To connect the speaker cords
Connecting a USB Mass Storage Class Device
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 33rd track, “PRG FULL” will appear.
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
To Replace the Battery in the Remote Control
Voltage selector (models other
than Australia and Hong Kong)
Before plugging in, confirm the
position of the voltage marker points
at. See page 1.
Press to fast-forward the track during playback.
To stop searching, press 6.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
The tracks are played back in the programmed order.
or
CD
USB
Lithium coin battery
(product number: CR2025)
USB memory
USB cable (not supplied)
Operations for Program Play (while program stop mode)
• To check the programmed contents, press SET repeatedly.
• To add tracks, repeat steps 2 and 3 above.
• To erase or exit the program, press 7.
(not supplied)
Press and hold
Press to fast-reverse the track during playback.
To stop searching, press 6.
or
– The stored program is not kept.
Change display
information
Press repeatedly.
DISPLAY
NOTES:
NOTES:
Playing at Random—Random Play
•
When connecting with a USB cable, use the USB 2.0 cable whose length is less than 1 m.
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• USB mass storage class device is charged through the USB MEMORY REC/PLAY
terminal except when set to ECO Mode. Some USB mass storage class device may be
charged through the USB terminal only when “USB” is selected as the source.
• You cannot connect a computer to the USB MEMORY REC/PLAY terminal of the
System.
• Do not disconnect the USB mass storage class device while playing back a file. It may
cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect and connect the USB mass storage class device again after turning
off the System.
NOTES:
Press so that the RND (random) indicator lights up and random
play starts.
RANDOM
1
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
Release
Insert
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” or “NO DATA” appears on the main display.
Operations for Random Play
• To skip a track, press ¢.
Red
• To go back to the beginning of the current track, press 4.
• To exit from random play, press RANDOM so that the RND (random) indicator
disappears during playback.
RESUME Play
Press RESUME to activate RESUME Play so that the RESUME indicator lights up.
When you stop the playback by one of the following operations, “RESUME”
appears and this System stores the beginning of the stopped track on the disc or
USB mass storage class device.
To a wall outlet
Plug the AC power cord only after all connections are complete.
• If the wall outlet does not match the AC plug, use the supplied
AC plug adapter (not supplied for Hong Kong and Australia).
– Pressing 7 once
Prohibiting Disc Ejection (on the System only)
– Changing the source
From left
speaker
From right
speaker
You can lock the disc tray so that no one can eject the loaded disc while the
System is on standby.
When you start playback again, playback starts from the beginning of the
stopped track.
CAUTION:
Black
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Press these buttons for 2 seconds while the System is on
standby.
To cancel the prohibition, repeat the same procedure.
NOTES:
To clear the memory, open the disc tray, disconnect the USB mass storage class
device or press 7 twice.
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• When you clear the memory and start playback, playback starts from the first
track.
To deactivate RESUME Play, press RESUME again.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
2
4
Scarica from Www.Somanuals.com. All Manuals Search And Scarica.
|